|  | May 22, 2008
The "GTA-PC" April 14, 2007
The "Digg" Case January 19, 2007
The "ITX-Laptop" December 07, 2006
The "Tortoise Beetle" October 02, 2006
The "DOS Head Unit" August 31, 2006
The "Janus Project" August 05, 2006
The "Leela PC" June 26, 2006
Nano-ITX in a Football May 17, 2006
The "EPIA Alloy Mod" April 11, 2006
Neatorama's Collection of Case Mods |
| | | | February 18, 2006
The "Rundfunker" October 24, 2005
The "ITX TV" October 06, 2005
The K'nex-ITX August 05, 2005
The "Waffle Iron PC" July 21, 2005
The "Supra-Server" July 18, 2005
The "Mega-ITX" July 07, 2005
The "Encyclomedia" May 25, 2005
The "Accordion ITX" May 16, 2005
The "FileServerRouterSwitch" May 15, 2005
The "Mini Falcon" May 13, 2005
The "Bender PC" May 11, 2005
The "BBC ITX B" May 10, 2005
The "Frame" April 20, 2005
The "Jeannie" March 09, 2005
The "Cool Cube" January 30, 2005
First Nano-ITX Project? January 17, 2005
The "iGrill" January 15, 2005
The "Gumball PC" December 15, 2004
The "Deco Box" December 03, 2004
The "TERA-ITX" |
| | | | October 06, 2004
The "Coealacanth-PC" September 17, 2004
The "Gramaphone-ITX-HD" August 26, 2004
The "C1541 Disk Drive ITX" August 25, 2004
The "SEGA-ITX" August 13, 2004
The "Quiet Cubid" August 06, 2004
The "BMWPC" July 14, 2004
The "Moo Cow Moo" July 02, 2004
The "Mini Mesh Box" June 17, 2004
Jukebox ITX May 24, 2004
The "ERN005PC" (KANA) March 13, 2004
The "Underwood No. 5" February 04, 2004
The "Humidor CL" January 23, 2004
The "Attache Server" January 22, 2004
"Racing The Light" January 21, 2004
VIA's Flat Panel DevKits January 20, 2004
The "Ambulator I" January 19, 2004
The "Borg Appliance" December 19, 2003
The Gingerbread Village Server December 04, 2003
Custom PC's XmasTreePC December 01, 2003
"Windows XP Box" Full alphabetical archive on right hand side of page... |
| |
|
The "Humidor II"
By Jeffrey
L. Stephenson - Posted on November 21, 2002
Tail end of PSU
brick being lifted up to clear cables then....
The 95W PSU comes
up and out then rests on the table without anything being
disconnected! The PSU has two 4-pin connectors and one floppy-style
connector.
Unfinished inside
interface opening. The height of the PSU opening is 3/4"
taller than it needs to be. This creates a "slot"
underneath the electrical box, which passes cables and air.
The motherboard is mounted sideways so that the cables have
to make an immediate right turn to exit out under the PSU.
This is what I
call the money shot. It shows the cabling and routing in detail.
The extra long wireless receiver cable was wound up and stowed.
Hard drive to the left. Tip of LED light at forefront of picture.
ThermalTake memory cooler to the right. I especially like
the mesh fit over the USB light. I didn't pull it all the
way past the bulb. Instead I left excess mesh around the light,
which creates a more subtle effect.
Back door shot. This has been my most challenging
design idea. A single rectangular cut in the back of a wooden
box, such as the size of this 75ct humidor, solved the problem.
It doesn't matter if the EPIA-M has a different connector
layout. It also allows me to pursue the umbilical style of
cable system management.
|
|
