Enter the Mini-ITX.com online store

Projects

September 05, 2017
Choosing the right DC-DC PSU

August 27, 2015
AMD's Project Quantum

August 13, 2015
The Redstone PC is the ultimate Mini-ITX Minecraft Machine

October 09, 2014
The "Restomod TV"

April 09, 2013
Installing NAS4Free

February 28, 2013
Building an XBMC 12 Home Theatre PC

January 25, 2011
XBMC Guide updated to version 10.0

August 06, 2010
Building a Green PC

February 15, 2010
Building an ION powered HTPC with XBMC

October 10, 2008
The "Cambridge Autonomous Underwater Vehicle 2008"

Mini-ITX Online Store

September 12, 2008
"Florian", the DVD burning robot

September 05, 2008
The "i-EPIA"

May 22, 2008
The "GTA-PC"

April 14, 2007
The "Digg" Case

January 19, 2007
The "ITX-Laptop"

December 07, 2006
The "Tortoise Beetle"

October 02, 2006
The "DOS Head Unit"

August 31, 2006
The "Janus Project"

August 05, 2006
The "Leela PC"

June 26, 2006
Nano-ITX in a Football

May 17, 2006
The "EPIA Alloy Mod"

April 11, 2006
Neatorama's Collection of Case Mods

February 18, 2006
The "Rundfunker"

October 24, 2005
The "ITX TV"

October 06, 2005
The K'nex-ITX

August 05, 2005
The "Waffle Iron PC"

July 21, 2005
The "Supra-Server"

July 18, 2005
The "Mega-ITX"

July 07, 2005
The "Encyclomedia"

May 25, 2005
The "Accordion ITX"

Mini-ITX Online Store

May 16, 2005
The "FileServerRouterSwitch"

May 15, 2005
The "Mini Falcon"

May 13, 2005
The "Bender PC"

May 11, 2005
The "BBC ITX B"

May 10, 2005
The "Frame"

April 20, 2005
The "Jeannie"

March 09, 2005
The "Cool Cube"

January 30, 2005
First Nano-ITX Project?

January 17, 2005
The "iGrill"

January 15, 2005
The "Gumball PC"

December 15, 2004
The "Deco Box"

December 03, 2004
The "TERA-ITX"

October 06, 2004
The "Coealacanth-PC"

September 17, 2004
The "Gramaphone-ITX-HD"

August 26, 2004
The "C1541 Disk Drive ITX"

August 25, 2004
The "SEGA-ITX"

August 13, 2004
The "Quiet Cubid"

August 06, 2004
The "BMWPC"

July 14, 2004
The "Moo Cow Moo"

July 02, 2004
The "Mini Mesh Box"

Full alphabetical archive on right hand side of page...


The "Windows XP Box"
By Andy France
Posted on 1 December 2003
Jump to:

Introduction

I needed a small Windows XP machine and a Mini-ITX board was the obvious choice. So I decided to build my "Windows XP Box" in a Windows XP box. The external dimensions of the box are a tiny 243mm x 200mm x 48mm.

Click image to magnify

My requirements were:

  • Use as powerful a motherboard as possible for the size i.e. a Nehemiah EPIA M10000.
  • It must have an internal CD drive (this size eating requirement turned out be be very hard to meet).
  • No bits could be cut off the motherboard to make it fit.
  • The box must not bulge in an unsightly way, nor can the box be made bigger.
  • It must not burst into flames when working hard (this should always be a requirement of a computer project).

 Fortunately there is no longer any requirement for an internal floppy drive. That would have have defeated me.

Construction

The bits arrive and it looks like an impossible task, with too many bits to fit in a small space.

Click image to magnify

I nearly gave up and decided it was an impossible task. The Windows XP box was 3mm thinner and 12 mm narrower than the Adobe Acrobat box I had measured up when first deciding if the project was going to be possible. The challenge was to arrange the components into a 3D jigsaw, then decide how to build enough of an internal support case to get everything to stay in place.

Eventually it looked like I might have a possible layout, but the tolerances were tight. I had 6mm to spare on the long internal dimension of the box and only 3mm to spare on the thickness of the box, and this was not allowing for any thickness for the internal support case that holds everything in place.

Click image to magnify

In order to mount all the bits I was going to have to make an inner support case that would tightly slide into the cardboard box. I chose Wonderboard plastic as my construction material because it is reasonably strong and very easy to work with (it cuts with a Stanley knife). It would have been nice to use aluminium, but the cramped design made the chances of a short circuit too great.

The first construction step was to cut out a base plate the exact size of the inside of the cardboard box and double check where the bits will fit.

As the Wonderboard was 3mm thick this reduced my tolerance in two dimensions to zero. The CD drive would touch one side of the inner support case. The deep part of the CD drive would touch the heat sink on the motherboard, with the narrow bit being able to overlap it, and the far side of the motherboard touches the other side of the Wonderboard case. In the other dimension it was even harder. The top of the sound connector would touch the support case, and the underside of the motherboard would touch the cardboard box. Fortunately the hard drive can slide under the motherboard as this is above (below?) the unused PCI slot. The only place left for the PSU was above the hard drive with the bulky connectors facing down towards the CD both to the front and the back of the hard drive.

Click image to magnify

Now I could position the CD drive hard against the side and start assembling the support case. In the next picture you can see the step up between the thin part of the CD drive and the thicker part of the main body of the drive. The heat sink on the Mini-ITX board touches this step.

Click image to magnify

After much cutting and half a tube of glue the case was finished. I built pillars to support three corners of the motherboard and the power supply and added brackets to support the CD and the hard drive. In such a compact design cooling was a concern so I made fan mounting points in opposite corners of the case. To keep the CPU nice and cool I cut a hole for it it the side of the case and glued in a couple of plates to act as ducting so the CPU fan will only suck in cold outside air. The other two fans are the exhaust points. The fan guards were cut out of a metal speaker grill using an angle grinder as neatly drilling that many holes is just not fun. Angle grinders are almost as much fun to use as chain saws.

Click image to magnify


Board Finder
Case Finder
Mini PC Finder