Vehicle Enclosures

In this section...

Vehicle PSUs M2-ATX 160W 6-24V, M2-ATX 140W 6-32V and picoPSU-style Plug-In M3-ATX 6-24V Vehicle PSUs compatible with the VoomPCs and other cases*

Intelligent Vehicle PSU Kits

Our intelligent Vehicle PSU kits will provide a regulated output to your Mini-ITX board, while monitoring the battery of your vehicle. Rapid voltage changes are protected against, and graceful timed shutdowns are possible. These require more auto-electrical knowledge than our Easy-Install kits, but if you have the time and the inclination, are well worth it.

M2-ATX 160W Intelligent Wide Input 6-24V Vehicle/Battery DC-DC Power Supply

M2-ATX Vehicle DC-DC Power Supply, 6-24V 160W
  SPECIAL OFFER - was £45.00
£42.00 
  £50.40 inc. VAT
  IN STOCK (Checked 07:31 BST)

You may also require (see notes*)

Short Molex to P4 Power Cable
£3.50 
  £4.20 inc. VAT
  IN STOCK (Checked 07:31 BST)

12V P4 to 12V P4 Power Extension Cable
£2.50 
  £3.00 inc. VAT
  IN STOCK (Checked 07:31 BST)

AC/DC Barrel Connector Cable (useful for testing with one of our AC Adapters)
£3.50 
  £4.20 inc. VAT
  IN STOCK (Checked 07:31 BST)
 

Designed to provide power and to control the ON/OFF switch of a motherboard (PC) based on ignition status, M2-ATX is a wide input (6-24V) vehicle or general purpose battery powered application DC-DC ATX power supply capable of surviving tough car engine cranks (down to 5.7V) as well as transient over-voltage situations.

8 user selectable microcontroller driven timing modes, allowing you to choose up to 8 ignition/shutdown vehicle / car timing schemes. While in deep sleep mode, M2-ATX constantly monitors your car battery voltage levels, automatically shutting down until battery levels reach safe levels.

M2-ATX comes equipped with ATX, Molex HDD, SATA HDD and Floppy cable harness, jumpers, faston connectors and 2 pin cables for motherboard ON/OFF switch. Just connect it to your 12V or 24V car/boat/RV battery and power up your PC.

Designed to work with your own projects or the VoomPC and VoomPC 2, but is also a direct size compatible replacement with Morex 26xx, 27xx, 36xx, Travla C134, C150, C158, C159, Compact Wall Mount cases. Dimensions: 45mm x 160mm (1.77in x 6.31in). 160W Output - ideal for Socket Mini-ITX boards. Not compatible with EPIA PD boards.

*Notes: If your board has a 4 pin 12V P4 power connector, you will need add a Molex to 12V P4 Power Cable or 12V P4 to 12V P4 Power Extension Cable.

Product Manual (PDF)

M2-ATX-HV 140W Intelligent Very Wide Input 6-32V Vehicle/Battery DC-DC Power Supply

M2-ATX-HV Vehicle DC-DC Power Supply, 6-32V 140W
  SPECIAL OFFER - was £49.00
£42.00 
  £50.40 inc. VAT
  IN STOCK (Checked 07:31 BST)

You may also require (see notes*)

Short Molex to P4 Power Cable
£3.50 
  £4.20 inc. VAT
  IN STOCK (Checked 07:31 BST)

12V P4 to 12V P4 Power Cable
£2.50 
  £3.00 inc. VAT
  IN STOCK (Checked 07:31 BST)

AC/DC Barrel Connector Cable (useful for testing with one of our AC Adapters)
£3.50 
  £4.20 inc. VAT
  IN STOCK (Checked 07:31 BST)
 

Designed to provide power and to control the ON/OFF switch of a motherboard (PC) based on ignition status, M2-ATX-HV is a wide input (6-32V) vehicle or general purpose battery powered application DC-DC ATX power supply capable of surviving tough car engine cranks (down to 5.7V) as well as transient over-voltage situations.

8 user selectable microcontroller driven timing modes, allowing you to choose up to 8 ignition/shutdown vehicle / car timing schemes. While in deep sleep mode, M2-ATX-HV constantly monitors your car battery voltage levels, automatically shutting down until battery levels reach safe levels.

M2-ATX-HV comes equipped with ATX, Molex HDD, SATA HDD and Floppy cable harness, jumpers, faston connectors and 2 pin cables for motherboard ON/OFF switch. Just connect it to your 12V or 24V car/boat/RV battery and power up your PC.

Designed to work with your own projects or the VoomPC and VoomPC 2, but is also a direct size compatible replacement with Morex 26xx, 27xx, 36xx, Travla C134, C150, C158, C159, Compact Wall Mount cases. Dimensions: 45mm x 160mm (1.77in x 6.31in). 160W Output - ideal for Socket Mini-ITX boards. Not compatible with EPIA PD boards.

*Notes: If your board has a 4 pin 12V P4 power connector, you will need add a Molex to 12V P4 Power Cable or 12V P4 to 12V P4 Power Cable.

Product Manual (PDF)

M3-ATX PicoPSU Form-Factor 125W Intelligent Wide Input 6-24V Vehicle/Battery DC-DC Power Supply

M3-ATX Intelligent Vehicle DC-DC Power Supply
£45.00 
  £54.00 inc. VAT
  IN STOCK (Checked 07:31 BST)

You may also require

Short Molex to P4 Power Cable (*see note)
£3.50 
  £4.20 inc. VAT
  IN STOCK (Checked 07:31 BST)

M3-ATX Serial Cable Harness (Type 1))
£4.50 
  £5.40 inc. VAT
  IN STOCK (Checked 07:31 BST)

AC/DC Barrel Connector Cable (useful for testing with one of our AC Adapters)
£3.50 
  £4.20 inc. VAT
  IN STOCK (Checked 07:31 BST)
 

Designed to provide power and to control the ON/OFF switch of a motherboard (PC) based on ignition status, M3-ATX is a wide input (6-24V) vehicle or general purpose battery powered application DC-DC ATX power supply capable of surviving tough car engine cranks (down to 6V) as well as transient over-voltage situations.

The M3-ATX is based on an electrically similar design to the M2-ATX but with dramatic size reductions (picoPSU plug-in style).

  • 125 Watts (150watt peak) PSU
  • 20pin ATX, 6-24V wide input range
  • Programmable timing settings using optional serial harness and utility
  • Intelligent shutdown controller
  • ON/OFF motherboard control
  • Survives vehicle engine cranks
  • Battery deep discharge prevention
  • High efficiency, 125 watts output
  • "Anti-Thump" Amplifier remote control
  • < 0.5mA standby current
  • Solid Japanese Polymer capacitors

M3-ATX comes equipped with a ATX, Molex HDD, SATA HDD and Floppy cable harness, jumpers, faston connectors and cables for Thump and Motherboard ON/OFF switch. Just connect to your 12V or 24V car/boat/RV battery and power up your PC.

Programmable shutdown / sleep modes via optional serial cable; Fits any motherboard equipped with a 20 or 24pin ATX connector; 100% silent, fanless, no moving parts; Operates from 6-24V; Multi-chemistry batteries supported; Highly efficient design - does not produce a lot of heat; Ideal for low power Intel Core processors as well as all Atom, VIA or AMD processors.

*Note: If your board has a 4 pin 12V P4 power connector, you will need add a Molex to 12V P4 Power Cable. Not compatible with Zotac NM10-E board due to positioning of P4 connector on board.

M3-ATX Manual

M3-ATX Timing Settings

M3-ATX-HV PicoPSU Form-Factor 95W Intelligent Very Wide Input 6V-34V Vehicle/Battery DC-DC Power Supply

M3-ATX-HV Intelligent Vehicle DC-DC Power Supply
£45.00 
  £54.00 inc. VAT
  IN STOCK (Checked 07:31 BST)

You may also require

Short Molex to P4 Power Cable (*see note)
£3.50 
  £4.20 inc. VAT
  IN STOCK (Checked 07:31 BST)

M3-ATX Serial Cable Harness (Type 1))
£4.50 
  £5.40 inc. VAT
  IN STOCK (Checked 07:31 BST)

AC/DC Barrel Connector Cable (useful for testing with one of our AC Adapters)
£3.50 
  £4.20 inc. VAT
  IN STOCK (Checked 07:31 BST)
 

Designed to provide power and to control the ON/OFF switch of a motherboard (PC) based on ignition status, M3-ATX-HV is a very wide input (6-34V) vehicle or general purpose battery powered application DC-DC ATX power supply capable of surviving tough car engine cranks (down to 6V) as well as transient over-voltage situations.

The M3-ATX-HV is based on an electrically similar design to the M2-ATX but with dramatic size reductions (picoPSU plug-in style).

  • 95 Watts (120watt peak) PSU
  • 20pin ATX, 6-34V wide input range
  • Programmable timing settings using optional serial harness and utility
  • Intelligent shutdown controller
  • ON/OFF motherboard control
  • Survives vehicle engine cranks
  • Battery deep discharge prevention
  • "Anti-Thump" Amplifier remote control
  • Low standby current
  • Solid Japanese Polymer capacitors

M3-ATX-HV comes equipped with a ATX, Molex HDD, SATA HDD and Floppy cable harness, jumpers, faston connectors and cables for Thump and Motherboard ON/OFF switch. Just connect to your 12V or 24V car/boat/RV battery and power up your PC.

Programmable shutdown / sleep modes via optional serial cable; Fits any motherboard equipped with a 20 or 24pin ATX connector; 100% silent, fanless, no moving parts; Operates from 6-34V; Multi-chemistry batteries supported; Highly efficient design - does not produce a lot of heat; Ideal for low power Intel Core processors as well as all Atom, VIA or AMD processors.

*Note: If your board has a 4 pin 12V P4 power connector, you will need add a Molex to 12V P4 Power Cable. Not compatible with Zotac NM10-E board due to positioning of P4 connector on board.

M3-ATX-HV Manual

M3-ATX Timing Settings

M4-ATX 250W Intelligent Wide Input 6-30V Vehicle/Battery DC-DC Power Supply

M4-ATX Vehicle DC-DC Power Supply, 6-30V 250W
£59.00 
  £70.80 inc. VAT
  IN STOCK (Checked 07:31 BST)


More images of the M4-ATX

You may also require (see notes*)

USB Header to Header Cable for M4-ATX
£2.50 
  £3.00 inc. VAT
Lead time approx 1-3 days
 

The M4-ATX is a wide input (6-30V) vehicle or general purpose battery powered application DC-DC ATX power supply capable of surviving tough car engine cranks (down to 6V) as well as transient over-voltage situations. The M4-ATX is programmable by DIP Switches and by USB and can control the ON/OFF switch of a motherboard based on ignition status.

The M4-ATX has user selectable microcontroller driven timing modes allowing you to choose up to 8 ignition/shutdown timing schemes (including a regular PSU mode, when the M4-ATX behaves just like a regular ATX PSU). While in deep sleep mode, the M4-ATX can constantly monitor your battery voltage levels, automatically shutting down until battery levels reach safe levels.

Programmable by USB: The M4-ATX can be connected to a USB header on a PC and monitored/programmed with the Windows System Tray Monitor & Application or through a Linux API.

The M4-ATX comes equipped with ATX cable harness, 12V P4 Power Cable and 2pin cable for motherboard ON/OFF switch. Just connect it to your 12V or 24V car/boat/solar battery and power up your PC.

Designed to work with your own projects. Dimensions: 122mm x 94mm (4.8in x 3.7in). 250W Output (300W peak) - ideal for Socket Mini-ITX boards.

Product Manual (PDF)

Don't see what you want here? Send us an email with as much information as possible, and we'll try and get it for you.


Reckoner

Cards accepted:
Secure Shopping:

Contact Us

Store: +44 (0) 845 475 8 475

Store enquiries: store@mini-itx.com

Other enquiries: feedback@mini-itx.com

Visit the Store

Click here to enter the online store

Social

Follow us on Twitter!

Join our Mailing List

Copyright: All content on this site is Copyright © 2002-2014 Mini-ITX.com and respective owners, all rights reserved.