Jetway MI97R-30 Fanless 1.83GHz Quad Core Celeron Mini-ITX Board with 12V DC Input (JNF9T Replacement)

Mini-ITX Board with fanless 1.83GHz Intel Quad Core N2930 Bay Trail-M processor and integrated 313MHz - 854MHz Intel HD Graphics. Up to 8GB of system memory supported on 1x 8GB DDR3L SODIMM. Realtek RTL8119I Gigabit Ethernet and High Definition Realtek ALC888 4 Channel HD Audio with 3W Speaker Amplifier. SATA, PCI Express x1, 3x M.2 Slots (B, E, M).

JNF9T Replacement: This board is the nearest replacement to the JNF9T-2930, with identical back panel design but also several differences including: The JNF9T had Mini PCI-E, mSATA, Intel 82583V Ethernet; The MI97R has M.2 Type-E (for WiFi), M.2 Type-B (for WWAN), M.2 Type-M (for SATA M.2 Storage), Realtek RTL8119I Ethernet. Both boards have 1x SATA.

Rear Panel Connectors: +12V 2.5mm Regulated DC-In Power Jack, 1x Parallel Port, 1x HDMI (1920×1200@60Hz), 1x VGA (1920×1200@60Hz), 1x Combined PS/2 Mouse/Keyboard Port, 3x USB 2.0, 2x RS232 Serial, 1x Gigabit Ethernet, 1x USB 3.0, 2x 3.5mm Audio (Line Out, Mic In).

Board Connectors: 1x 2pin 12V alternate power connector (Molex 5566-2 connector, cannot be used at the same time as the external DC input); 1x 4pin Power out (Male FDD Molex, cable required); 1x DDR3L SODIMM Socket; 1x PCI-Express x1; 1x M.2 2230 Type-E Slot (USB/PCIe, for WiFi cards); 1x M.2 3042 Type-B Slot (USB with SIM holder, for WWAN cards); 1x SATA 3Gb/s; 1x M.2 2242/2280 (SATA, for Storage); 3x RS232 Serial headers (+5V/+12V); 4x USB 2.0 headers on 2x 9pin connectors; 1x 8-bit GPIO; 1x 24bit dual channel LVDS header/inverter (1920×1200@60Hz); 1x eDP (2560×1600@60Hz, co-layout with LVDS); AT/ATX Mode Jumper; 1x 4-pin Fan Header; 1x 5pin SMBUS header; Front Panel Header; 1x 9-pin Audio Header.

12V DC Power input: The MI97R requires a 12V AC Adapter to power the board and feed power to a SATA device through a power-out connector (cable available optionally here). If you are using M.2 SATA storage, a cable is not required. There is an alternate 12V input on a 2pin Molex 5566 connector which can also be used (though not at the same time as the rear input). We sell several enclosures without power supplies, or you can bypass the PSU on any other compatible Mini-ITX case.

Powering from an ATX PSU: To power using an ATX PSU, an ATX Bridging Plug can be connected to the ATX connector of the PSU, and the 12V P4 plug (Black/Yellow cables) connected to the motherboard. Use the AT/ATX Mode jumper to control power up behaviour (AT Mode = power on immediately, ATX Mode = power when power switch pressed).

Windows 7/10 Support: Windows 7 32/64-bit and Windows 10 are supported on this motherboard.

Downloads: BIOS, Documentation and Drivers

Box Contents: Motherboard, I/O Shield. To use the SATA connector, a Female Floppy to SATA power cable is required.

*Note: The MI97R supports up to 8GB DDR3L memory on 1x 8GB 1.35V DDR3L SODIMM. This is not compatible with DDR, DDR2 or standard DDR3 SODIMM memory, available in the 'You may also require' section on the left.