Jetway JLI1BV-0L Fanless 2GHz Quad Core J6412 Thin-ITX Board with 12V DC Input, 2x Intel i225 2.5Gb LAN, M.2 NVMe/SATA, SATA, M.2 WiFi & M.2 WWAN, up to 6x COM Ports and up to 16GB RAM

2.5Gb-Ready Fanless board with ultra-low profile form factor (20mm high) powered by 2GHz (2.6GHz Burst) Intel Quad Core J6412 Elkart Lake processor and integrated 10th Gen Intel UHD Graphics. 2x Intel i225V 2.5Gb Ethernet Ports. Support for up to 16GB DDR4 SODIMM memory. M.2 NVMe/SATA and SATA storage, M.2 Type E Slot (WiFi) and Type B Slot (WWAN) and up to 6 COM ports.

Rear Panel Connectors: 12V regulated DC Input, VGA port (2560x1600 @60Hz max res); 2x Type-A USB 3.1 Gen1 Ports; 2x Type-A USB 2.0 Ports; 2x Intel i225V 2.5Gb Ethernet Ports; 3.5mm Line-Out and Mic Ports.

Board Connectors: 1x 4pin 12V alternate power connector (must not be used at the same time as the external DC input); 1x AT/ATX Power Mode Jumper; 1x M.2 2242/2280 Type-M Socket (supports NVMe at PCIe x2 and SATA); 1x SATA Port (6Gbps); 1x SATA Power Out (Cable included); 1x M.2 Type-E Socket (unpopulated, for Wi-Fi card, supports CNVi); 1x M.2 Type-B Socket (unpopulated, for 4G/5G USB 3342/3352 WWAN card); 2x RS232/485 Headers (2x COM to header cables provided, 2mm pitch); 4x RS232 Headers (2mm pitch); 1x I2C/SMBUS Header; 1x 8-bit GPIO Header (5V, 2mm pitch); 1x LVDS Header (2560x1600 @ 60Hz max res.); 1x eDP Header (4096x2304 @ 60Hz max res.); 1x DDR4 SODIMM Socket (3200MHz, up to 16GB); 4x USB 2.0 headers on 2x 9pin connectors; 1x USB 2.0 header on wafer connector; 1x 4-pin CPU Fan Header; 1x Front Panel Audio Header; 1x 3W Speaker Header; 1x FPANEL Header.

Important! This board has a 12V DC Power input and is not designed for use with a standard ATX PSU: The JLI1BV-0L requires a 12V AC Adapter to power the board and feed power to a SATA device through an on-board 4pin power output connector (cable included). There is an alternate 12V input on a 4pin Molex 5566 connector which can also be used (though not at the same time as the rear input). We sell several enclosures without power supplies, or you can bypass the PSU on any other compatible Mini-ITX case.

Suitable cases (without PSU): The following enclosures come without an internal PSU and are compatible with the JLI1BV-0L: M350 and M5X**.

Suitable cases (with PSU): All Mini-ITX Chassis can be used with the JLI1BV-0L if their PSU is bypassed and a 60W minimum 12V external AC Adapter is used. Alternatively an ATX Bridging Plug can be connected to the ATX connector of the PSU, and the 12V P4 plug (Black/Yellow cables) connected to the motherboard. Use the AT/ATX Mode jumper to control power up behaviour (AT Mode = power on immediately, ATX Mode = power when power switch pressed).

*Memory The JLI1BV-0L supports up to 16GB DDR4 memory on 1x 16GB DDR4 SODIMM, running at 3200MHz. This is not compatible with DDR, DDR2 or DDR3 SODIMM memory.

Box contents: Motherboard, SATA Data Cable, 30cm SATA Power Cable, Standard I/O Shield, 2x Serial Header to DB9 Cables.

Drivers and Manual: Manual; Windows 10 64-bit (v.1809+): Chipset, Graphics, Audio, LAN, IME; Windows 11 64-bit: Chipset, Graphics, Audio, LAN, IME, GPIO; Linux: GPIO