Gigabyte MZAPLAI Fanless 1.5-2.6GHz Quad Core J4025 Mini-ITX Board with 12V DC Input, 2x Gigabit LAN, PCIe x4; mSATA, 5x SATA (4 with Marvell RAID) and up to 6x COM Ports

Industrial Mini-ITX board with fanless 1.5GHz (2.6GHz Burst) Intel Quad Core J4025 Apollo Lake processor and integrated Intel UHD Graphics 505. VGA, HDMI, LVDS and eDP, 2x Gigabit Ethernet Ports, DDR3L memory support, mSATA and 5x SATA storage (4 ports with Integrated Marvell 88SE9230 RAID), PCIe x1 Slot, 2 external COM ports and 4 COM port headers.

Limited units remaining. This board is typically supplied only in quantity packaging and will be repackaged by us to ensure optimal protection.

Rear Panel Connectors: 12V regulated DC Input, 2x RS232/422/485 DB9 Serial Ports; VGA Port (up to 1920x1080 @ 60Hz); HDMI Port (up to 3840x2160 @ 30Hz); 2x Realtek RTL8111HS RJ45 Gigabit Ethernet Ports; 2x Type-A USB 2.0 Ports; 2x Type-A USB 3.0 Gen1 Ports; 3.5mm Line-Out, Mic and Line-In Ports.

Power Connectors: 1x 4pin 12V alternate power connector (must not be used at the same time as the external DC input); 1x AT/ATX Power Mode Jumper.

Expansion: 1x PCIe x1 (Gen2 x 1) Expansion Slot.

Storage Connectors: 5x 6Gbps SATA Ports (4 support RAID-on-motherboard 0/1/10 through Marvell 88SE9230 host controllers, 1 supports SATA DOM); 3x SATA Power Out (2 cables included, each supports 2 drives); 1x mSATA 6Gbps connector.

Graphics Headers: 1x LVDS Header (up to 1920x1280 @ 60Hz), 1x eDP Header (up to 3840x2160 @ 60Hz). VGA and HDMI connectors on the rear of the board. 3 independent graphics outputs supported.

Serial and USB Headers: 4x RS232 Headers; 2x USB 3.0 Gen1 headers on one connector; 2x USB 2.0 headers on one connector.

Fan Headers: 1x 4-pin CPU Fan Header; 1x 4-pin Chassis Fan Header.

Additional Board Headers: Audio Header; Backlight Control Header; Buzzer; Chassis Intrusion Header; Clear CMOS Jumper; GPIO Header; 2x LAN LED Connectors; RAID LED Header; 3x SATA Power Out Headers; SMBUS Header; 2W Speaker Header; System Front Panel Header; 14-pin TPM Module Connector.

12V DC Power input: The MZAPLAI requires a 12V AC Adapter to power the board and feed power to any SATA devices through 3 on-board 4pin power output connectors (2 cables included). There is an alternate 12V input on a 4pin Molex 5566 connector which can also be used (though not at the same time as the rear input). We sell several enclosures without power supplies, or you can bypass the PSU on any other compatible Mini-ITX case.

Powering from an ATX PSU: To power using an ATX PSU, an ATX Bridging Plug can be connected to the ATX connector of the PSU, and the 12V P4 plug (Black/Yellow cables) connected to the motherboard. Use the AT/ATX Mode jumper to control power up behaviour (AT Mode = power on immediately, ATX Mode = power when power switch pressed).

Suitable cases: The following enclosures come without an internal PSU and are compatible with the MZAPLAI : M350 and M5X**. Other Mini-ITX Chassis can be used with the MZAPLAI if their PSU is bypassed and a 60W minimum 12V external AC Adapter is used.

Memory: The MZAPLAI supports up to 16GB DDR3L memory on 2x up to 8GB DDR3L SODIMMs, running at up to 1866MHz.

Packaging: The MZAPLAI is an industrial board sold only in multi-packs. We have individually repackaged each board in recycled Mini-ITX board boxes.

Box contents: Motherboard, 2x SATA Power Cables (each cable can power 2 devices), Standard I/O Shield. If connecting a SATA device you will require a SATA data cable.

Drivers and Information: Quick Reference Guide; Windows 10: Chipset, Graphics, Audio, LAN, TXE, Marvell SATA/RAID Driver and Utility, Serial IO Driver, Ready Mode